Qiqiao
This is mainly because solid wood flooring has not been subjected to regular drying. Therefore, during installation, a layer of plastic film can be laid under the floor, on the one hand to prevent moisture and prevent the floor from lifting, on the other hand has a certain degree of sound insulation. In addition, the floor is placed in the room to be laid two or three days in advance so that the wood can adapt to the temperature of the room and it can also prevent warping.
Drum
Some floors, after being paved, are swollen and damp. This is mostly related to the environment around the floor, especially the base tide or floor water. In order to ensure that the floor does not play drums, we must pay attention to three points: First, at the end of the civil works, the solid wood floor cannot be laid immediately; Second, if the living room is in a humid environment, it is advisable to lay a moistureproof floor; Third, when laying, the floor The moisture content cannot be less than 6%.
Face
Using the slats of the same tree species, the colors will also have large differences. If it is not properly laid, it will easily show a "face". When using lacquered wood floors, especially when the species is extremely variegated, you should consider the choice and deployment of the slats so that the color of the floor changes from shallow to deep, or gradually from shallow to deep.
Dirty board
Refers to some of the floor paint, giving a dirty "gray" feeling, and some even the footprints are clearly visible. To prevent this from happening, it is important to pay attention to the fact that the surface of the board after polishing is kept clean.
sound
Due to the low quality of the floor laying, people will make a buzzing noise when walking on the floor and feel uncomfortable after hearing it. To this end, it should be noted that the keel and the ground, the floor and the keel bond firmly, the number and length of nails appropriate. At the same time, to prevent the keel spacing is too large or the moisture content is too high, otherwise drying and shrinkage after laying will also have a certain impact.
Quilting
Some floors spread over a few days and there was a large gap between the slats. This is mostly related to the high moisture content before the laying of the floor, and it shrinks due to the high temperature or air drying in the room. Note that the moisture content of the floor prior to laying should be in the range of 8% to 13%, and be timely oiled after being laid.
Insects
Because of the biting of insects in the wood, the floor surface can often see a pile of powder, which is annoying. The reason is related to the floor selection. To prevent worms:
The first is to purchase floors that have been produced by the steaming process of the kiln. Although the price is relatively expensive, all the eggs in the wood have been killed.
The second is to carefully select the keel, and all those who have wormhole or bark should not use it.
This is mainly because solid wood flooring has not been subjected to regular drying. Therefore, during installation, a layer of plastic film can be laid under the floor, on the one hand to prevent moisture and prevent the floor from lifting, on the other hand has a certain degree of sound insulation. In addition, the floor is placed in the room to be laid two or three days in advance so that the wood can adapt to the temperature of the room and it can also prevent warping.
Drum
Some floors, after being paved, are swollen and damp. This is mostly related to the environment around the floor, especially the base tide or floor water. In order to ensure that the floor does not play drums, we must pay attention to three points: First, at the end of the civil works, the solid wood floor cannot be laid immediately; Second, if the living room is in a humid environment, it is advisable to lay a moistureproof floor; Third, when laying, the floor The moisture content cannot be less than 6%.
Face
Using the slats of the same tree species, the colors will also have large differences. If it is not properly laid, it will easily show a "face". When using lacquered wood floors, especially when the species is extremely variegated, you should consider the choice and deployment of the slats so that the color of the floor changes from shallow to deep, or gradually from shallow to deep.
Dirty board
Refers to some of the floor paint, giving a dirty "gray" feeling, and some even the footprints are clearly visible. To prevent this from happening, it is important to pay attention to the fact that the surface of the board after polishing is kept clean.
sound
Due to the low quality of the floor laying, people will make a buzzing noise when walking on the floor and feel uncomfortable after hearing it. To this end, it should be noted that the keel and the ground, the floor and the keel bond firmly, the number and length of nails appropriate. At the same time, to prevent the keel spacing is too large or the moisture content is too high, otherwise drying and shrinkage after laying will also have a certain impact.
Quilting
Some floors spread over a few days and there was a large gap between the slats. This is mostly related to the high moisture content before the laying of the floor, and it shrinks due to the high temperature or air drying in the room. Note that the moisture content of the floor prior to laying should be in the range of 8% to 13%, and be timely oiled after being laid.
Insects
Because of the biting of insects in the wood, the floor surface can often see a pile of powder, which is annoying. The reason is related to the floor selection. To prevent worms:
The first is to purchase floors that have been produced by the steaming process of the kiln. Although the price is relatively expensive, all the eggs in the wood have been killed.
The second is to carefully select the keel, and all those who have wormhole or bark should not use it.
Nature floor del floor paint
DQOK Bathroom Single Cold Basin Faucet With Simple And Unique Design, DQOK Basin Faucet Created According To People's Living Habits, Create High Cost Performance Modern /Classical High-quality Brass/304 stainless steel Faucets Makes You Creat A Wonderful And Conformtable Bathroom. DQOK Bathroom Basin Faucets Have CUPC, NSF/ANSI 61, Low-Lead,SASO,KC and CE certificates.
Single Cold Basin Faucet,Matte Black Basin Faucet,Button High Basin Faucet,Handle Single-Cold Basin Faucet
Heshan Dingquan Sanitary Ware Industry Co., Ltd , https://www.dqoksanitary.com